title-bar.jpg (6912 bytes)
Company ProfileOur ProjectsProducts & ServicesResource CenterWhat's NewOnline Form
Site Map
Contact Information
Back To Home
indexad.jpg (12436 bytes)

Copyright ©1998-2007:
AMKO Systems Inc.
All rights reserved.

Please fill out and submit the following form to request information and provide us with feedback regarding this web site.

1. CUSTOMER INFORMATION
Contact Name:
Title:
Department:
Company Name:
Address:
City:
Province/State:
Postal/Zip Code:
Country:
Telephone:
Fax:
Email:
Send more information on the following: Product name (specify)
    
  Service (specify)
    
  Company Profile
Send information by: Email the information.
  Mail the information to our office.
  Fax the information to our office.
  Have a representative call our office.
Additional request:
Project:
Plant Type:
Plant Location:
City:

Date:

2. MEASURING COMPONENTS
Which components/parameters are to be measured?

Measured components

Ranges
  Measuring range(s) Physical unit*

Dust

Gas velocity / volumetric flow rate
Temperature
Pressure
CO
O2
CO2
NO
NO2
NOx
SO2
HCl
NH3
H2O

*ppm, mg/m3, grains/ft3, °C, °F, kPa, "H2O, psig, mm Hg, m/s, etc.

3. SOURCE DETAILS

3.1 Plant details:
Furnace Fuel:
Process Type:
3.2 Monitoring objective:
Regulatory compliance
Process control
Combustion control
Emission monitoring
Other

3.3 Compliance and regulatory requirements:
US EPA Env. Canada 1/PG/7 Revised AEP CEMS Code Local Air Permit
Not required

4. CONDITIONS AT MEASUREMENT LOCATION

Gas composition

Concentration range
(physical unit*)

*ppm, mg/m3, grains/ft3, °C, °F, kPa, "H2O, psig, mm Hg, m/s, etc.
Does the sample gas represent an explosion hazard when combined with air? No Yes
Mounting/extraction location: indoor outdoor
Mounting position: vertical horizontal or (specify)
Cross section: circular rectangle square
Duct material: steel brick other
Duct/stack outer diameter: mm±1% (without insulation)
Wall thickness: mm
Insulation thickness: mm
Double-walled stack: No Yes
Inner wall material: St 37 (carbon steel)
stainless steel
Inner lining (e.g. refractory): No Yes thicknessmm
Ambient temperature*: min: °C
max: °C
normal: °C
Plant elevation: m (above sea level)
Atmosphere*:  

potentially explosive:

 No Yes, zone:

aggressive:

 No yes, which component:
Weather-proof cover necessary? No Yes
Purge air supply necessary? No Yes
* At mounting/extraction location

5. SAMPLE GAS DETAILS
Gas temperature: min: °C
max: °C
normal: °C
Water dewpoint temperature: min: °C
max: °C
normal: °C
Acid dewpoint temperature: min: °C
max: °C
normal: °C
Gas velocity at measure location: min: m/s
max: m/s
normal: m/s
Measuring gas pressure: min: kPa
max: kPa
normal: kPa
Dust content: min: mg/m³
max: mg/m³
normal: mg/m³
Contamination due to aerosol: no
yes, which

6. DETAILS OF THE MEASURING SYSTEM

6.1 Measuring technique
Preferred or required measuring technique.

Component in-situ extractive
Dust
Gas

6.2 Specifications: in-situ system

Power supply:  

Analyzer:

 115 VAC/60Hz
230 VAC/60Hz

Purge air unit:

 115 VAC/60Hz single phase
220 up to 240 VAC/60Hz single phase
345 up to 415 VAC/60Hz 3 phase
380 up to 480 VAC/60Hz 3 phase Other
Mounting location (evaluation unit): indoor outdoor  
Compressed air connection: no
yes  Pressure:
Analog output: 4 - 20 mA 0 - 20 mA

6.3 Specifications: extractive system

Power supply: 115 VAC/60Hz
230 VAC/60Hz
Mounting location (analyzer): indoor
outdoor
Construction: rack
field device installation:
Ambient temperature*: min: °C
max: °C
normal: °C
Explosion protection*: no yes, zone:
Analyzer enclosure required: no yes
Sample line: length:m
heated: no   yes
Probe heating: no yes
Condensate drainage available: no yes, specify
Sample gas return path: no yes, return path length:
m
Mounting flange on-site: no
yes, material:
type / dimensions:
Certified according to:
*At analyzer location

7. DATA ACQUISITION & REPORT GENERATION SYSTEM
DARS (Preferred):
Computer
Chart recorder
Paperless recorder
Existing on-site system
Other
Not required
8. REMARKS

footer.jpg (10448 bytes)